Welcome to China Electronic protection components official website!

Support Hotline
0769-83811196
东莞雅迅专业的技术支持

Minimum temperature control switch size and parameters

Article Source:Thermostat factoryAuthor:Yaxun ElectronicsPopularity:Published time:2017-03-19 10:48

Minimum temperature control switch size and parameters
China's lithium batteries are widely used in mobile phones, laptops, electric bicycles, electric vehicles, power tools, digital cameras and many other downstream areas,Power storage capacity in the lithium battery demand accounted for only about 2%While in mobile phones and notebook computers accounted for as high as 38% and 24%.Lithium battery overheating protection is also more and more important,These lithium battery current and voltage is relatively small,To facilitate the thermal protection of these lithium batteries,Small temperature switch to get rapid development.
The current minimum temperature control switch is a square thermal protector,Product models are TB02 series,KW series, the standard product size: length * width * thick (11.5 * 5.0 * 2.4) mm,Lead length can be customized according to customer requirements.Dongguan Yaxun minimum temperature control switch has two kinds of shell:
Molded Case Size: Length 15 * Width 5.4 * Height 2.4
Steel Case Size: Length 11.5 * Width 5.0 * Height 2.4

Performance
   3.1 Rated current
       4A / DC12V, 3A / DC24V, 3A / AC115V, 2A / AC250V
   3.2 Disconnection temperature: 30 ℃ ~ 155 ℃ Reset temperature 20 ℃ ~ 110 ℃ (see drawing).
   3.3 Tensile test:The lead end of the product should be able to withstand greater than or equal to 20N tension,The wire is broken and slipped out.
   3.4 insulation voltage: a. Products in the disconnect between the lead should be able to withstand AC660V,Which lasted 1min without breakdown flashover phenomenon;
            B. Product lead and insulation shell can withstand AC1800V,Lasted 1S without breakdown flashover phenomenon;
   3.5 Insulation resistance: Under normal conditions,The insulation resistance between the lead and the insulating housing is above 100MΩ. (Using the table for the DC500V megger)
   3.6 contact resistance: the product contact resistance should not be greater than 50mΩ.
   3.7 high temperature test:
A. product is placed higher than the rated operating temperature of 20 ℃ air environment maintained 96h;
                  B.5 min The limit temperature is 180 ° C
4.3.1 normally closed type
TB02-BB8D - Molded Case Product Model           TB02-BB1D - Iron Case Product Model
          XXX ℃ - Rated breaking temperature          XXX ℃ - Rated breaking temperature
    4.3.2 normally open type
       TB02-KA8D - Molded Case Product Model     TB02-KA1D - Iron Case Model
          XXX ℃ - Rated breaking temperature          XXX ℃ - Rated breaking temperature

     5.Temperature parameter table:
No. Operating temperature Reset temperature No. Operating temperature Reset temperature
30 30±3℃ ≥20℃ 95 95±5℃ 70±15℃
35 35±3.5℃ ≥25℃ 100 100±5℃ 70±15℃
40 40±4℃ ≥30℃ 105 105±5℃ 75±15℃
45 45±4.5℃ ≥33℃ 110 110±5℃ 75±15℃
50 50±5℃ ≥35℃ 115 115±5℃ 80±15℃
55 55±5℃ 42±6℃ 120 120±5℃ 85±15℃
60 60±5℃ 45±8℃ 125 125±5℃ 85±15℃
65 65±5℃ 48±10℃ 130 130±5℃ 90±15℃
70 70±5℃ 50±12℃ 135 135±5℃ 95±15℃
75 75±5℃ 53±14℃ 140 140±5℃ 100±15℃
80 80±5℃ 55±15℃ 145 145±5℃ 100±15℃
85 85±5℃ 60±15℃ 150 150±℃ 105±15℃
90 90±5℃ 65±15℃ 155 155±5℃ 110±15℃

Product size and structure:
Minimum temperature control switch size and structure
Technical Guide: <Ksd9700 Temperature Switch Inspection Rules>